Mounting A Tub
Mounting A Tub
Blog Article
We've encountered this great article involving How to Install a Bathtub Yourself listed below on the internet and accepted it made sense to share it with you on my blog.
Setting up a tub isn't specifically rocket science, yet it does require solid plumbing, carpentry, as well as often, tiling abilities. Changing an old bathtub with a new one is also a moderately tough job. If the old tub is easily easily accessible, the job can move rapidly; if you have to open a wall to remove the old tub and also place the brand-new bath tub, the job is a lot harder. In either case, the task is within a house handyman's skills, although you will need a helper to vacate the old bathtub as well as set in the new one. Make sure you have actually certified on your own for the task and fit trying it. Instead of employing a contractor to take control of a halfway-completed job, it is much better to think about employing one before you start. Opportunities are you may require a specialist plumber to make tube connections.
This short article will aid you mount a new bathtub in your shower room if you have already bought a brand-new tub and do not need to change the setup of your previous water system pipes.
Your devices and also material checklist need to make up the following:
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your setup, then the first thing you need to do is detach the supply of water. After doing so, activate the faucets to drain any kind of water staying in the system. The process of getting rid of the existing taps can be fairly troublesome due to the limited gain access to that is usually the situation.
Use a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the taps. Have a towel prepared for the continuing to be water that will originate from the pipes. As soon as the supply pipes have actually been eliminated, make use of the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming during this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will need to be cleaned of any type of old sealing substance.
Before going on to fit the new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic connector to prevent damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end gives a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will call for minimizing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, position the tap in the placing hole in the bath/basin making certain that the washers remain in place in between the faucet as well as the sink. Safeguard the tap in place with the supplier given backnut. When the faucet is securely in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with regular faucet adapters. The former type needs to be connected to the tap finishes initially, tightening only by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Installing the Tub
Utilizing both wood boards under its feet, place the tub in the needed placement. The wooden boards are useful in uniformly spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 small points.
The next objective is to make certain that the bathtub is leveled all round. This can be achieved by inspecting the level and adjusting the feet on the tub up until the spirit level checks out degree.
To mount taps, fit all-time low of the outermost adaptable faucet connector to the suitable supply pipe by making a compression join; after that do the exact same for the various other faucet.
Activate the water system and also examine all joints and also brand-new pipework for leakages and also tighten them if essential. Load the tub as well as additionally examine the overflow electrical outlet and also the regular electrical outlet for leakages.
Ultimately, take care of the bathroom paneling as explained in the maker's user's manual. Tiling and also securing around the bath tub must wait till the bath tub has actually been used at least once as this will settle it right into its last setting.
Getting ready for the Setup
First of all, the supporting frame supplied with the bath needs to be fitted (if needed) according to the maker's directions. Next, fit the taps or mixer to the tub. When fitting the tap block, it is essential to ensure that if the tap includes a plastic washer, it is fitted between the bath and the taps. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets system to prevent strain on the bath tub.
Fit the adaptable faucet ports to the bottom of the two taps using 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. See to it you utilize all of the supplied washing machines.
Link the trap to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom must now be ready to be suited its final position.
Tiling Around the Bath tub
In the location where the bath fulfills the ceramic tile, it is required to secure the accompanies a silicone rubber caulking. This is very important as the fitting can relocate sufficient to crack a stiff seal, causing the water to pass through the wall between the bathroom and the tiling, bring about issues with dampness and also possible leakages to the ceiling listed below.
You can choose from a selection of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes as well as cartridges, and are capable of securing spaces as much as a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of drenched newspaper or soft rope. Remember to constantly fill up the bathtub with water prior to securing, to allow for the activity experienced when the bathtub is in use. The sealer can split fairly very early if you do not think about this movement prior to sealing.
Conversely, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise conveniently available on the marketplace. It is a good idea to fit the tiles utilizing waterproof or waterproof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am just very taken with How to Install a Bathtub and I hope you liked the new blog entry. So long as you liked our page please remember to share it. We take joy in reading our article about Tools You Need to Install a New Bathtub .
Click Here!
Report this page